Skip to main content
SpringerLink
Log in

Proceedings of the Twenty-First International Machine Tool Design and Research Conference

Held in Swansea, UK, 8th-12th September, 1980

  • Conference proceedings
  • © 1981

Overview

Editors:
  1. J. M. Alexander

    1. University College of Swansea, UK

    View editor publications

    You can also search for this editor in PubMed   Google Scholar

This is a preview of subscription content, log in via an institution to check access.

Access this book

Log in via an institution

Other ways to access

Licence this eBook for your library

Institutional subscriptions

Table of contents (79 papers)

  1. Front Matter

    Pages i-x
    Download chapter PDF

  2. Opening Address

    1. Opening Address

      • M. C. de Malherbe
      Pages 1-4

  3. Forming: Theoretical

    1. Front Matter

      Pages 5-5
      Download chapter PDF

    2. Optimal Use of Visioplasticity Analysis

      • P. Boissonneau, J. Oudin, Y. Ravalard
      Pages 7-12

    3. Simulation of Contact Pressure Distribution on Tool Surface by Ubet

      • M. Kiuchi, Y. Murata
      Pages 13-20

    4. Plastic Analysis of Flange Wrinkling in Axisymmetrical Deep-Drawing

      • B. Kaftanoglu
      Pages 21-28

    5. Analysis of Strip Rolling as an Adiabatic Process

      • Betzalel Avitzur, Andrzej Nowakowski
      Pages 29-32

    6. Residual Stresses at Various Types of Plastic Superficial Deformation

      • Michael Kobrin
      Pages 33-38

    7. Control of a Servohydraulic Press for the Simulation of Hot Strip Rolling with the Plane Strain Compression Test

      • L. Peichl, R. Kaspar, O. Pawelski
      Pages 41-49

    8. Basic Studies of Roll Forging I

      • T. Hirai, Y. Maekawa, T. Katayama, J. B. Hawkyard
      Pages 51-56

    9. Basic Studies of Roll Forging II

      • T. Hirai, Y. Maekawa, T. Katayama, J. B. Hawkyard
      Pages 57-62

    10. Optimum Roll Pass Schedules on the Cold Roll Forming Process of Symmetrical Channels

      • T. Jimma, H. Ona
      Pages 63-67

    11. Analysis of Roll Torque in Profile Ring-Rolling of L-Sections

      • D. Y. Yang, J. S. Ryoo, J. C. Choi, W. Johnson
      Pages 69-74

    12. An Investigation into the Possibility of Roll Peen-Forming: Some Experimental Results

      • N. R. Chitkara, W. Johnson
      Pages 75-84

    13. On the Peen-Forming of Metals

      • W. Johnson, A. G. Mamalis, S. K. Ghosh
      Pages 85-93

    14. An Upper Bound Solution for the Extrusion of Square Section from Round Bar through Converging Dies

      • S. Hoshino, J. S. Cunasekera
      Pages 97-105

    15. Effective Fitting Pressure Distribution in the Design of Extrusion Dies

      • Tsuneo Hirai, Toshikazu Ishise
      Pages 107-113

    16. On the Cropping of Single Tubes and Tube Bundles

      • A. N. Tilakasiri, J. M. Alexander
      Pages 115-122

    17. A Pneumatic Accelerating Device Installed on Press Machine and its Application to High Speed Cropping

      • N. Yanagihara, H. Saito, T. Nakagawa
      Pages 123-128

    18. A Low Cost Blanking Tool with Bainite Steel Sheet Laminated

      • T. Nakagawa, K. Suzuki
      Pages 129-138
Back to top

Keywords

Editors and Affiliations

  • University College of Swansea, UK

    J. M. Alexander

Bibliographic Information

  • Book Title: Proceedings of the Twenty-First International Machine Tool Design and Research Conference

  • Book Subtitle: Held in Swansea, UK, 8th-12th September, 1980

  • Editors: J. M. Alexander

  • DOI: https://doi.org/10.1007/978-1-349-05861-7

  • Publisher: Red Globe Press London

  • eBook Packages: Engineering, Engineering (R0)

  • Copyright Information: Macmillan Publishers Limited 1981

  • Edition Number: 1

  • Number of Pages: X, 631

  • Additional Information: Previously published under the imprint Palgrave

  • Topics: Manufacturing, Machines, Tools, Processes

Publish with us

Policies and ethics

Back to top

Search

Navigation