Skip to main content
SpringerLink
Log in

Proceedings of the Twenty-fourth International Machine Tool Design & Research Conference

  • Conference proceedings
  • © 1984

Overview

Editors:
  1. B. J. Davies

    1. Department of Mechanical Engineering, University of Manchester Institute of Science and Technology, Manchester, UK

    View editor publications

    You can also search for this editor in PubMed   Google Scholar

This is a preview of subscription content, log in via an institution to check access.

Access this book

Log in via an institution

Other ways to access

Licence this eBook for your library

Institutional subscriptions

Table of contents (58 papers)

  1. Front Matter

    Pages i-xi
    Download chapter PDF

  2. Metal Forming and Shearing

    1. Front Matter

      Pages 1-1
      Download chapter PDF

    2. Evaluation of Roll Loads and Torques in Strip and Section Rolling: Theory Versus Experiment

      • A. R. Ragab, M. E. Said, Y. El-Halaby
      Pages 3-11

    3. Production of Jointless Light Alloy Cycle Wheel Rims by Ring Rolling

      • K. F. Hutcheon, J. B. Hawkyard
      Pages 13-18

    4. Ring Rolling; the Inclusion of Pressure Roll Speed for Estimating Torque by Using a Velocity Superposition Method

      • J. S. Ryoo, D. Y. Yang, W. Johnson
      Pages 19-24

    5. Cold Extrusion — Pre-Programmed Efficiency?

      • Winfried Beisel
      Pages 25-30

    6. Temperature Study of the Dynamic Plane Strain Compression Test

      • P. A. Atack
      Pages 31-36

    7. Characteristic Deformation Modes and Working Pressures in Static Heading of Short, Thick Walled Axi-Symmetric Tubular-Rods

      • N. R. Chitkara, C. M. Leech, J. M. Hale
      Pages 37-45

    8. Pressing of Aluminium in the Molten State in the Manufacture of Aluminium-Copper Conductor (Cable) Joints

      • J. Grzéskowiak
      Pages 47-49

    9. Elasto-Plastic Finite Element Analysis of Hydrostatic Extrusion with Various Mathematically Contoured Dies

      • Wang Xutang, Jin Qijian, Xie Shueisheing
      Pages 51-57

    10. Elastic Stresses and Strains in the Mandrel during the Extrusion and Drawing of Tubes

      • Bela Lengyel, M. J. M. B. Marques
      Pages 59-64

    11. Determination of the Pressure Distribution Over the Tool Surface in Cold Forging

      • V. Maegaard
      Pages 65-72

    12. On the Hot Extrolling of Aluminium

      • J. M. Alexander, K. Hatakeyama
      Pages 73-83

    13. A New Experimental Technique for the Measurement of Mean Coefficient of Friction in the Direct Drawing of Section Rod From Round Bar

      • B. B. Basily
      Pages 85-88

    14. Ironing with Heavy Reduction

      • N. H. Nielsen, N. Bay, N. K. Frederiksen
      Pages 89-96

    15. Analysis in Workability of Pipe Bending Using High Frequency Induction Heating

      • H. Asao, K. Okada, M. Watanabe, H. Yonemura, T. Matsumoto, N. Umehara
      Pages 97-104

    16. Deep Drawing with Hydrodynamic Lubrication

      • Jehuda Tirosh, Peter Konvalina
      Pages 105-110

    17. Warm Press Shaving of Gear Parts

      • M. Murakawa, K. Ohkawa, N. Koga, K. Suzuki, T. Nakagawa
      Pages 111-118

    18. Precision Cropping Under Axial Load for Shaped Workpieces

      • Chen Jinde, Zhang Zigong, Xion Guanghan, Yu Dehong, Tang Zhaojiu
      Pages 119-125

    19. The Strip Peeling of Steels

      • M. H. Walters, T. H. C. Childs
      Pages 127-134
Back to top

Keywords

Editors and Affiliations

  • Department of Mechanical Engineering, University of Manchester Institute of Science and Technology, Manchester, UK

    B. J. Davies

Bibliographic Information

Publish with us

Policies and ethics

Back to top

Search

Navigation